Crystal Image Technologies KVM-16RH Bedienungsanleitung

MAN005 Rev Date 2/11/2014 UNIMUX-DVI(A)-xHD USB DVI KVM Switch Installation and Operation Manual

NTI UNIMUX SERIES USB KVM SWITCH 6 INSTALLATION 1. It is not necessary to turn the CPUs or monitors OFF during this installation. 2. Connect a

NTI UNIMUX SERIES USB KVM SWITCH 7 5. Connect each CPU to the USB switch using a USB-DHEXT-xx-MM (xx=3, 6, 10, or 15 foot) cable for each vide

NTI UNIMUX SERIES USB KVM SWITCH 8 RS232 Connection If the RS232 is going to be used, connect one end of the CAT5 patch cable (supplied) to the port

NTI UNIMUX SERIES USB KVM SWITCH 9 Power-Up Sequence For optimum performance and communication of DDC information between the monitor and CPU, we r

NTI UNIMUX SERIES USB KVM SWITCH 10 USING THE UNIMUX DVI KVM SWITCH Once the UNIMUX is properly connected, the UNIMUX will enable a connection to be

NTI UNIMUX SERIES USB KVM SWITCH 11 Selects a specific port Configure port to connect To a MAC CPU Configure port to connect To a WINDOWS or S

NTI UNIMUX SERIES USB KVM SWITCH 12 Select Country Code It is possible to configure the UNIMUX to emulate a specific international Sun keyboard reg

NTI UNIMUX SERIES USB KVM SWITCH 13 RS232 CONTROL RS232 enables the UNIMUX to be remotely controlled via RS232. To control the UNIMUX via RS232

NTI UNIMUX SERIES USB KVM SWITCH 14 DIP SWITCH UNIT ADDRESS 8 7 6 5 OFF OFF OFF OFF 0 (not valid) OFF OFF OFF ON

NTI UNIMUX SERIES USB KVM SWITCH 15 Command Protocol RS232 commands supported by the unit are defined below. All command strings should be termin

i TRADEMARK UNIMUX is a trademark of Network Technologies Inc in the U.S. and other countries COPYRIGHT Copyright © 2000, 2014 by

NTI UNIMUX SERIES USB KVM SWITCH 16 NTI Switch Control Program For Windows 9X, NT, 2000, XP, Vista, and 7 The NTI Switch Control Program is an eas

NTI UNIMUX SERIES USB KVM SWITCH 17 8) Change Volume for Audio Output/User (not applicable to this model) - change Audio port output volume 9)

NTI UNIMUX SERIES USB KVM SWITCH 18 CASCADING The UNIMUX supports cascading of multiple UNIMUX switches, with access to downstream PCs provided thr

NTI UNIMUX SERIES USB KVM SWITCH 19 KEYBOARD FEATURES The keyboard configuration of each CPU is saved in the UNIMUX. For example, if the CPU attac

NTI UNIMUX SERIES USB KVM SWITCH 20 Figure 15-

NTI UNIMUX SERIES USB KVM SWITCH 21 DDC The UNIMUX is designed to transfer DDC information from the monitor to the CPU so that the CPU is able to u

NTI UNIMUX SERIES USB KVM SWITCH 22 TROUBLESHOOTING PROBLEM: Keyboard Errors SOLUTION: Check cable connections on each CPU and the switch. PROBL

NTI UNIMUX SERIES USB KVM SWITCH 23 INDEX addressing, 13 Audio support, 21 Autostatus, 15 baud rate, 13 Broadcast mode, 11 Command mode, 10 control

ii TABLE OF CONTENTS INTRODUCTION...

iii Figure 15- Keyboard Layouts...

NTI UNIMUX SERIES USB KVM SWITCH 1 INTRODUCTION The UNIMUX-DVI-xHD 4,8,16 or 32-Port USB DVI KVM switch (UNIMUX) allows access to up to thirty two

NTI UNIMUX SERIES USB KVM SWITCH 2 MATERIALS Materials supplied with this kit: • NTI UNIMUX-DVI-xHD (4,8,16 or 32 ports) USB DVI Video KVM Switch

NTI UNIMUX SERIES USB KVM SWITCH 3 DEFINITIONS • USB Composite Device A USB device that contains multiple endpoints each representing

NTI UNIMUX SERIES USB KVM SWITCH 4 FEATURES AND FUNCTIONS 1. CPU Select Switches- push to manually switch to a spe

NTI UNIMUX SERIES USB KVM SWITCH 5 RACKMOUNTING INSTRUCTIONS This NTI switch was designed to be mounted to a rack or to sit on a desktop. It inc